PENDING Automatic site-wide client push installation does not work

[Bojan Živković]

I installed SCCM 2012 R2 from scratch in my test domain environment. Having done all you did automatic site-wide client push installation does not work at all. In ccm.log there is no single entry about successful/failed installation as if automatic site-wide client push installation is not enabled. Meanwhile (just in case) I created new subnet in AD Sites and Services (192.168.8.0/24) and assigned it to Default-First-Site-Name and now I am waiting to see if anything will change.

 

[Prajwal Desai]

Try using the IP address ranges instead of subnets. If there is no entry in ccm.log file then the client push is not working.

 

[Bojan Živković]

Is this some bug or something is misconfigured? Current boundary is Default-First-Site-Name (Active Directory site type) and it was created automatically after Active Directory Forest Discovery was enabled. Why on all computers with IP address in subnet 192.168.8.0/24 (assigned to Default-First-Site-Name) installation of client is not initiated?

 

[Bojan Živković]

Having created subnet and assigned to Default-First-Site-Name clients have been installed.

 

[Maunil Mehta]

Why on all computers with IP address in subnet 192.168.8.0/24 (assigned to Default-First-Site-Name)
For this Query , below is the answer
Because,
Ip address must have a subnet to help several facilities to send message to Main primary site about
Replication, Authentication and Service location for any application policies apply through GPO

 

[Maunil Mehta]

Now, if you have created subnet and assign to default, are you still does not see any entry in ccm.logs.. Please update us

 

[Bojan Živković]

All test domain computers are on subnet 192.168.8.0/24, after creating that subnet in AD Sites and Services and assigning it to Default-First-Site-Name site client's installation finally started on all computers where they should so (servers and workstations - not site servers and domain controllers). Each computer was shown in ccm.log and after a while all these computers appeared in console as computers with installed client. Obviously without subnet-site mapping in AD there were no computers belonging to AD site hence no client installation took place. I made simply oversight but eventually I solved problem.

Site membership of domain computer is vital, I know that of course. AD, Exchange, SCCM and other technologies rely heavily on site concept. Simply I have forgotten to create mapping.

 

[Maunil Mehta]

Ok Thanks Bojan. Then we can marked this thread as solved.
Hi Prajawal : Please marked this thread as solved.

 

[Bojan Živković]

Thank you Maunil, by the way may I ask you something (or to post new thread) about installing/unistalling Office 2016 using SCCM 2012 R2. I have trouble with command to uninstall it - setup.exe /uninstall ProPlus /config .\uninstall.xml.

 

[Maunil Mehta]

Hi Bojan,
You have to post new thread for new query as we need to marked this open thread to solved.

 

[Pawan Kumar]

All test domain computers are on subnet 192.168.8.0/24, after creating that subnet in AD Sites and Services and assigning it to Default-First-Site-Name site client's installation finally started on all computers where they should so (servers and workstations - not site servers and domain controllers). Each computer was shown in ccm.log and after a while all these computers appeared in console as computers with installed client. Obviously without subnet-site mapping in AD there were no computers belonging to AD site hence no client installation took place. I made simply oversight but eventually I solved problem.

Site membership of domain computer is vital, I know that of course. AD, Exchange, SCCM and other technologies rely heavily on site concept. Simply I have forgotten to create mapping.

Hi All

I am also having same issue, auto client push installation not started yet, I just checked all subnets are already created and assigned to sites. no logs were created in ccm.log for even trying client installation. if I push client manually then it will be installed successfully, plz help.