pxe

Hi everyone. I'm having issues to make PXE boot work. I have setup with Primary and Secondary site. Both sites have PXE boot enabled, SSL configured (clients are showing that they use PKI) and they are configured for different boundary rules. On Secondary site PXE is enabled with WDS...

Hi all! We changed our Site Server from Server 2012R2 to Server 2022 by using sccm recovery. This process was successful, exept our pxe isn't workling properly. Our clients are visible in SMSPXE.log and WDS Event Logs, but after Msg Type: 5=Ask and successfuly transfered bootmgfw.efi they are...

Hi, We're having a weird issue. When PXE imaging computers of the same model type, one PC will image properly, another wont. The next may, the next wont. No consistency. Any ideas.

Hello, We have run into a problem with one customer where their devices can't deploy from one DP which is weird because the same device model can be deployed from the same DP but in a different country. One is based in Thailand and the other one is in Australia. They are using the same DP for...

Hi Everyone, I have an issue which started a week ago after I updated the Boot images (from what I recall that is all I did). The client computer boots to PXE and loads the boot image (x64 and it has an IP Address assigned), when the boot image finishes loading instead of showing the Task...

Hi, I have SCCM 2103 in our network. UEFI PXE boot was working until 2 weeks back. But now it's throwing error 0x102. When checked SMSPXE.log, I see 'no advertisements found' message, which is strange. Only change in server was installing September 2021 security updates. Googling didn't help...

Hello We have just set up a new MECM server on a flat domain with around 350 endpoints. I must also add that this installation has replaced an existing, now redundant, MECM installation which we turned off a couple of weeks ago. For context, the boundaries of the old MECM were turned off and the...

I can confirm that SCCM detects the client's MAC address but somehow fails to deploy the task sequence which is deployed to unknown computers. In the SMSPXE log file it says - Using Task Sequence deployment BCS20004, but the client machine is not receiving anything. Please refer to the log...

Hello all, i have the issue that i cant upload a custom boot image to one of the DPs although it was possible on the others. Attached the smspxe log from the DP where it didnt worked. Any help much appreciated

I have been having issues with setting up PXE Boot I have the feature enabled and WDS installed letting PXE Boot install it, I had installed it myself first then enabled PXE Boot before but I was getting the same errors so I Disabled PXE Bood uninstalled WDS and then let SCCM install WDS when I...

Hi, I was trying to install an operating System (win-10) on unknown computer colection through SCCM PXE but was unsuccessful. My Scenario DHCP , SCCM, WDS on one server AD and DNS on another server Client - Virtual Machines created in Virtual BX I enabled PXE support for unknown computers...

Hello Guys, i have a problem with the SCCM when it comes to the PXE boot. The PXE boot starts normally up to "Preparing Network Properties" because a reboot happens and the smsts.log is created. Win2012 R2 SCCM 2012 R2 Same Network Segment What I've been tried or cleared up so far is: The...

Hi, I have been unable to boot from PXE from my system. Any computer I try to boot from it I get: PXE-E55: ProxyDHCP service did not reply to request on port 4011 I'm able to deploy an image from USB, but not PXE. Boot images have been configured to boot from pxe and distribution point has...

Hi all, I am facing problems to delpoy an image of Windows 10. I got the following message as unknown. Deploy Windows 10 x64 as required. Device xpto User Not applicable Status Type Unknown Description No messages have been received. If I deploy it as available, no messages returned...